Vasant Group
Vasant Group

MITTAL PRECISION PRESSURE DIE CASTING LLP

Turbos

The main function of turbo chargers is to enhance the mass of air entering the engine to create more power. Being a quality centric organization, we source these chargers from trustworthy suppliers .

Turbos

Brake Calipers

Aluminum A356 brake calipers were produced on different days, each a single continuous run, with the CSIR-RCS and a high-pressure die casting (HPDC) machine.

Brake Calipers

Knuckles

A knuckle is that part which contains the wheel hub or spindle, and attaches to the suspension and steering components. It is variously called a steering knuckle, spindle, upright or hub, as well.

Knuckles

Engine Cylinder Heads

In an internal combustion engine, the cylinder head (often informally abbreviated to just head) sits above the cylinders on top of the cylinder block. It closes in the top of the cylinder, forming the combustion chamber.

Engine Cylinder Heads

Engine Blocks & Pistons

The cylinder block is the portion of the engine between the cylinder head and sump (oil pan) and is the supporting structure for the entire engine. All the engine parts are mounted on it or in it and this holds the parts in alignment

Engine Blocks & Pistons

Engine Blocks

An engine block is the structure which contains the cylinders, and other parts, of an internal combustion engine. In an early automotive engine, the engine block consisted of just the cylinder block .

Engine Blocks

Gearbox Casing6

Gearbox casing is the main component in automobile world which is used to protect components inside the gearbox. It consists of gears, shafts, bearings and oil.

Gearbox Casings

Oil Pumps

The oil pump in an internal combustion engine circulates engine oil under pressure to the rotating bearings, the sliding pistons and the camshaft of the engine. This lubricates the bearings, allows the use of higher-capacity fluid bearings and also assists in cooling the engine.

Oil Pumps

LEAK TESTING MACHINE

A niche area of engineering, leak testing is sometimes referred to as pressure testing or vacuum testing. TQC has the knowledge and expertise to assist the customer from the basics, in specifying the acceptable leakage rate, or leak limit.

LEAK TESTING MACHINE

HARDNER TESTER

Hardness is a characteristic of a material, not a fundamental physical property. It is defined as the resistance to indentation, and it is determined by measuring the permanent depth of the indentation. ... The Rockwell test is generally easier to perform

HARDNER TESTER

SPECTRO METER

A spectrometer is any instrument used to probe a property of light as a function of its portion of the electromagnetic spectrum, typically its wavelength, frequency, or energy. The property being measured is usually intensity of light, but other variables like polarization can also be measured.

SPECTRO METER

DIE COAT MIXING UNIT

The device structure consist of Dilution or mixing tank to dilute water and lubricants, Storage tank,Regulator, Pumping tank , Stirrer, Fixed quantity pressure cylinder, pressurizing tank, pneumatic equipment and controllers packed in a common box.

DIE COAT MIXING UNIT

NITROGEN DE GASSING UNIT

This machine is used for removing hydrogen and other non metallic inclusions from molten aluminum. There is a hollow rotor with speed control by an A.C. drive.

NITROGEN DE GASSING UNIT

DENSITY UNIT

Density is a measurement that compares the amount of matter an object has to its volume. An object with much matter in a certain volume has high density. ... Density is found by dividing the mass of an object by its volume.

DENSITY UNIT

SKLENAR FURNACE FOR MELTING

Available from 300kg to 7000kg. Fuel : LDO, Furnace oil, Diesel, kerosene or gas.

SKLENAR FURNACE FOR MELTING

HOLDING FURNACE

Crucible furnaces are small capacity furnaces used for small melting applications or exclusively as holding furnaces. The metal is placed or poured into a ceramic crucible which is contained in a circular furnace that is fired by a gas burner or heated by electric elements.

HOLDING FURNACE

LEAK TESTING MACHINE

A niche area of engineering, leak testing is sometimes referred to as pressure testing or vacuum testing. TQC has the knowledge and expertise to assist the customer from the basics, in specifying the acceptable leakage rate, or leak limit.

LEAK TESTING MACHINE

HARDNER TESTER

Hardness is a characteristic of a material, not a fundamental physical property. It is defined as the resistance to indentation, and it is determined by measuring the permanent depth of the indentation. ... The Rockwell test is generally easier to perform

HARDNER TESTER

SPECTRO METER

A spectrometer is any instrument used to probe a property of light as a function of its portion of the electromagnetic spectrum, typically its wavelength, frequency, or energy. The property being measured is usually intensity of light, but other variables like polarization can also be measured.

SPECTRO METER

DIE COAT MIXING UNIT

The device structure consist of Dilution or mixing tank to dilute water and lubricants, Storage tank,Regulator, Pumping tank , Stirrer, Fixed quantity pressure cylinder, pressurizing tank, pneumatic equipment and controllers packed in a common box.

DIE COAT MIXING UNIT

NITROGEN DE GASSING UNIT

This machine is used for removing hydrogen and other non metallic inclusions from molten aluminum. There is a hollow rotor with speed control by an A.C. drive.

NITROGEN DE GASSING UNIT

DENSITY UNIT

Density is a measurement that compares the amount of matter an object has to its volume. An object with much matter in a certain volume has high density. ... Density is found by dividing the mass of an object by its volume.

To start your project with us

Contact Us